Exhaust Manifolds

Discussion in 'General Maverick/Comet' started by alaskamaverick, May 25, 2012.

  1. alaskamaverick

    alaskamaverick Member

    Joined:
    May 15, 2011
    Messages:
    400
    Likes Received:
    17
    Trophy Points:
    113
    Location:
    Spokane, WA
    Vehicle:
    1970 Maverick
  2. blugene

    blugene Senior member Supporting Member

    Joined:
    Jul 25, 2004
    Messages:
    10,768
    Likes Received:
    79
    Trophy Points:
    283
    Garage:
    1
    Location:
    Marietta, OK
    Vehicle:
    73 Comet GT, 72 Comet GT, 2008 "Comet" (our boxer, who is now in the galaxies)
    Those might be for a 302 but the design is not specific for a Mav?Comet.. I would bet they might not fit because ours are flatter as you may have noticed.
     
  3. alaskamaverick

    alaskamaverick Member

    Joined:
    May 15, 2011
    Messages:
    400
    Likes Received:
    17
    Trophy Points:
    113
    Location:
    Spokane, WA
    Vehicle:
    1970 Maverick
    I was afraid of that, finding that Maverick parts are harder to find these days. Thanks for the advice Blugene.
     
  4. ford84stepside

    ford84stepside Lone Wolf

    Joined:
    Nov 25, 2004
    Messages:
    4,038
    Likes Received:
    16
    Trophy Points:
    132
    Location:
    Berry Alabama
    Vehicle:
    1947 Lincoln Zephyr Coupe
    The drivers side Maverick manifold points down at an angle. I think those would run the exhaust straight into the firewall, probably not enough room for them to turn down then...
     
  5. alaskamaverick

    alaskamaverick Member

    Joined:
    May 15, 2011
    Messages:
    400
    Likes Received:
    17
    Trophy Points:
    113
    Location:
    Spokane, WA
    Vehicle:
    1970 Maverick
    I was wondering about that, I did notice the difference in the photos. There are some on the Forum for sale, but there pretty spendy. Plus shipping to AK is going to kill me. Thank you for the input.

    Does anybody know the part #'s I should be looking for?
     
    Last edited: May 26, 2012
  6. WesCoaster71

    WesCoaster71 Member

    Joined:
    Apr 29, 2012
    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    california
    Vehicle:
    1971 ford maverick A.O.D trans 302 5.0 cu
    i have a set from a lincon town car i would sell but i got my self some hooker headders pn# 6901 there low sweeping
     
  7. alaskamaverick

    alaskamaverick Member

    Joined:
    May 15, 2011
    Messages:
    400
    Likes Received:
    17
    Trophy Points:
    113
    Location:
    Spokane, WA
    Vehicle:
    1970 Maverick
    From a Lincoln town car? Would the fit? Did you put the 6901's on yet? How hard were they to install? I had one heck of a time taking the old ones off. Ended up cutting them off with a sawsall.
     
  8. alaskamaverick

    alaskamaverick Member

    Joined:
    May 15, 2011
    Messages:
    400
    Likes Received:
    17
    Trophy Points:
    113
    Location:
    Spokane, WA
    Vehicle:
    1970 Maverick
    Still looking for 302 exhaust manifolds to fit my 70 maverick...anybody?
     
  9. blugene

    blugene Senior member Supporting Member

    Joined:
    Jul 25, 2004
    Messages:
    10,768
    Likes Received:
    79
    Trophy Points:
    283
    Garage:
    1
    Location:
    Marietta, OK
    Vehicle:
    73 Comet GT, 72 Comet GT, 2008 "Comet" (our boxer, who is now in the galaxies)
  10. WesCoaster71

    WesCoaster71 Member

    Joined:
    Apr 29, 2012
    Messages:
    26
    Likes Received:
    0
    Trophy Points:
    0
    Location:
    california
    Vehicle:
    1971 ford maverick A.O.D trans 302 5.0 cu
    I still have mine
     
  11. blugene

    blugene Senior member Supporting Member

    Joined:
    Jul 25, 2004
    Messages:
    10,768
    Likes Received:
    79
    Trophy Points:
    283
    Garage:
    1
    Location:
    Marietta, OK
    Vehicle:
    73 Comet GT, 72 Comet GT, 2008 "Comet" (our boxer, who is now in the galaxies)

Share This Page